河北省石家莊高速公路服務區污水一體化處理設備項目

After-sale Service Warranty within and after Guarantee Period

1. Basic requirements of our after-sale service

1) If any quality problems such as design, manufacture, function or procedure occur within the

guarantee period, SCCW shall take full responsibility and bear all the economic losses incurred.

2) If any quality problems occurs within the guarantee period, SCCW shall provide on-site

service after receive the buyer’s notice in 24 hrs.

3) If any big quality problems occurs out of the guarantee period, SCCW will send maintenance

technician to provide visiting service after receive the buyer’s notice in 24 hrs and charge for a favorable price.

4) SCCW will provide a lifetime favorable price to the buyer with the materials and spare parts

used in system operation, equipment maintenance.

The above mentioned are only basic after-sale service requirements, we will make more promises related to quality assurance and operation guarantee mechanism.

2. After-sale service commitment

1) Quality and service commitment :

1.1 After-sale service department:

SCCW will set up a after-sale service department and spare parts center specified for Valin ArcelorMittal Automotive Steel Co.,Ltd Crane in Main Factory Building of Cold Rolling Project and provide professional equipment maintenance engineers.

1.2 Payment of maintenance expense:

All the maintenance expense within the guarantee period shall be borne by SCCW.

1.3 After-sale service measures within the guarantee period

The after-sale service work is an important part of our marketing and sales work. The quality of service provided will not only influence the company credit, but also closely relate to the safely running of the equipments. In order to maintain the good reputation of Hercules, SCCW will strictly observe relevant national regulations about Product-Quality Law and provide high quality products with the principle of hospitable reception, enthusiastic service, quick response and prompt resolution. We will conscientiously implement the after-sale service work in full-scale, and make commitment to our clients as follows:

1. Select and appoint engineering technicians and workers who are professionally

competent and personally committed to undertake the after-sale service work. Meanwhile set up the service office made up of chief engineer office, project office, technical center, after-sale service department and workshop specialists led and coordinated by marketing and sales department.

2. During the Valin ArcelorMittal Automotive Steel Co.,Ltd Crane in Main Factory

Building of Cold Rolling Project on-site installation and trial un, appoint specialized after-sale service personnel to work at the work place

高速公路服務區污水一體化設備的組成部分

　　高速公路服務區污水一體化設備由初沉池、接觸氧化池、二沉池、消毒池及消毒裝置、污泥池、風機房、風機組成，下面是詳細的介紹。

　　(1)初沉池：設備初沉池為豎流式沉淀池，污水在沉淀池的上升流速為0.6-0.7毫米/秒，沉淀下來的污泥用空氣提至污泥池。(注：WSZ-A O.5-5m3/h不設初沉池)

　　(2)接觸氧化池：初沉后水自流至接觸池進行生化處理，接觸池分為三級，總停留時間為 1小時以上。加強型設備接觸氧化時間可達6小時，填料為新穎梯形填料。易結膜、不堵塞。填料比表面積為160m2/m3，接觸池氣水比在12:1左右。(注WSZ-A 0.5-5T/h，接觸池為二級)

　　(3)二沉池：生化后污水流到二沉池，二沉池為二只豎流式沉淀池，它們并聯運行。上升流速為O.3-0.4毫米/秒。排泥采用空氣提升至污泥池。(注WSZ—A0.5-5mT/h，污泥自流到污泥池中)

　　(4) 消毒池及消毒裝置：消毒池按規范：“TJI4—74”標準為30分鐘，若是醫院污水，消毒池可增加停留時間至1-1.5小時，采用固體氯片接觸溶解的消毒 方式，消毒裝置能根據出水量的大小不斷改變加藥量，達到多出水多加藥，少出水少加藥的目的。其它消毒裝置可另行配制。(注：如用于工業污水消毒池與消毒裝 置可以不要)

　　(5)污泥池：初沉池、二沉池的所有污泥均用空氣提至 WSZ-A的污泥池內進行好氧消化。污泥池的清液回流至接觸氧化池內進行再處理。消化后剩余污泥很少，一般1-2年清理一次。清理方法可采用吸糞車從污泥 池的檢查孔伸入污泥底部，進行抽吸外運即可。(WSZ-A 0.5-5T/h，污泥采用厭氧消化)

　　(6)風機房、風機：設備 WSZ-A的風機房設在消毒池的上方，進口采用雙層隔音，進風口有消聲器、風機過濾器，因此運行時無噪音。風機采用二臺L型羅茨鼓風機，能自動交替運行。單臺風機運行壽命30000小時左右

　　以上就是高速公路服務區污水一體化設備六大組成部分，希望以上信息對大家有幫助。

河北省石家莊高速公路服務區污水一體化處理設備項目河北省石家莊高速公路服務區污水一體化處理設備項目